International journal of advanced computer technology (ijact) issn:2319-7900 89 design and analysis of crane hook with different material design and analysis of crane hook with different material patel ravin b, patel bhakti k, patel priyesh m, patel dixit h. International journal of advanced computer technology (ijact) crane hooks are highly liable components and are always subjected to failure due to accumulation of large engineering from gujarat technological university, ah-madabad, gujarat in 2012 the student of final year be.
Hooks to make certain you are using the appropriate hooks on your lifting equipment and to have them checked for fatigue, call the konecranes service nearest you for a hook assessment and hook repair. • scheduling a non-destructive test and inspection for crane and hoist hooks at the time of the periodic load test, and testing and inspecting before use new replacement hooks and other hooks suspected of having been overloaded. The daily to monthly inspection intervals for crane hooks shall be determined by the frequent and periodic inspection criteria of section 2-211 through 2-213 of ansi/asme b302-1990 (attached) inspection of hooks found to be deformed or cracked shall comply with 179(j)(2)(iii. Figure 27 load chart (taken from mra engineering report) boom or the jib hooks a few days prior to the incident, the crane was situated on worth street mra also produced a document “crane engineering calculation” on december 3, 2015, revised on december 30, 2015.
Engineering, 2011, 3, 935-941 crane hooks are highly liable components and are always subjected to failure due to accumulation of large amount of stresses which can eventually lead to its failure to study the stress pattern of crane hook in its stress analysis of crane hook and validation by photo-elasticity. Avon engineering designs and manufactures lifting solutions our goal is to design lifting equipment that increases your productivity and provides your personnel with a safe method of handling your product. Damage factor estimation of crane-hook (a database approach with image, knowledge and simulation) table 22 the values of dimension parameters.
Handling systems international is an industry leader in overhead crane manufacturing and design based in chicago, this family owned business has been providing quality made jib cranes, bridge cranes, and gantry cranes, since 1957. Reverse engineering expedited delivery options hooks hooks shall meet the manufacturer's recommendations and shall not be overloaded to make certain you are using the appropriate hooks on your lifting equipment and to have them checked for fatigue, access your crane usage data,. The base and ball hook system is an attachment that is designed to be used on the lunar surface as an improved alternative to the common crane hook and eye system. Construction industry | construction incidents investigation engineering reports the crane was assembled at the site with a 420' boom, 240' mast, 61' spar and 836,000 pounds of main counterweight attached to the spar an additional 836,000 pounds of auxiliary counterweight was to be attached to its pendants suspended from the mast tip at.
Avon engineering designs and manufactures lifting solutions and experienced in addressing the specific needs found in heavy industrial applications. Crane hooks are the components which are used to lift heavy loads using wire ropes and cranes in constructional sites and industries [2, 3] it is basically a hoisting fixture with pulley elongated by a rope or a. All of columbus mckinnon’s heavy-duty crane hooks and specialty parts are made in house at our 82,000 square foot facility in hamm, germany with our own forging, machining and tool-making capabilities, & utility engineering offshore technology plant manufacturing nuclear technology railway engine construction product overview.
Based on asme comments, you recommended that the june 13 occupational safety and health administration (osha) memorandum addressed to you, on the inspection requirements of overhead crane hooks, be revised. The crane operator was attempting to lay down the crane in high wind when the crane suddenly collapsed and overturned the crane had a luffing jib, 371 ft long and a 194 ft long boom there was no load on either the boom or the jib hooks. Osha safety program - crane & hoist safety share 0 share +1 0 tweet 0 (lifting equipment) of mechanical engineering design safety standards (latest edition) • all crane and hoist hooks shall have safety latches • hooks shall not be painted (or re-painted) if the paint previously applied by the manufacturer is worn.
Takuma nishimura obtained as the results of the fem analysis the database is used to identify the load conditions that were fatal to those damaged crane-hooks. Abstract— crane hook is very significant component used for lifting the load with the help of chain or wire ropes crane hooks are highly liable components and are always international journal of current engineering and scientific research (ijcesr) issn (print): 2393-8374, (online): 2394-0697,volume-2, issue-2,2015.
Overhead crane safety and inspection requirements notice maintain, and operate a crane or associated lifting equipment to read and to comply with the contents of the instruction manuals furnished by the manufacturer of the crane or associated lifting hook hook latch. The base and ball hook system is an attachment that is designed to be used on the lunar surface as an improved alternative to the common crane hook and eye system the design proposed uses an omni-directional ball hook and base to overcome the design problems associated with a conventional crane hook.